Tips From the Moving Company Pros: Ways To Move a Pinball Maker



With pinball making a substantial resurgence throughout the nation, Gentle Giant wishes to ensure that these timeless, lovely machines stay damage-free while being carried. Oh, and we desire individuals moving them to be safe, too.

In the beginning glimpse, pinball makers can appear intimidating to move because of their fragility, size, and weight. The good news is, our experienced Giants have a few techniques up their sleeves to guarantee your pinball is moved with ease.
Folding Down the Headbox

Most of modern pinballs (made in the last 20 years or two) have a hinge system which permits the headbox to be folded down. Early pinball makers had their headboxes bolted on, using either two or four bolts. All Electro-Mechanical pinballs utilize this system, in addition to the early Strong State machines.

Later devices have hinges and utilize a locking system to keep the headbox upright. There might also be two bolts inside as added security, in case the lock is broken or mistakenly un-latched.
Electro-Mechanical Pinballs

For Electro-Mechanical pinball machines, you need to eliminate the headbox rear gain access to panel to get access to the bolts and plugs within. Usually this panel has a lock on it to keep it in place, but in time the secret might have been lost. Rather often, there is a screw keeping this panel in place.

Once inside, eliminate the bolts and disconnect the big connectors that have wiring going down into the device. You might wish to identify these connectors to put them back in the right spot, but they ought to be various sizes, making it tough to plug back improperly.

You can now get rid of the headbox completely, or fold the headbox down onto the playfield glass. Make sure you use some foam, heavy cardboard, or blankets to safeguard the headbox from rubbing on the cabinet. Foam is best, as it will help keep the back glass in location.
Early Strong State Pinballs

For early Strong State Pinballs, you will have to get rid of the back glass. There is a lock located on the headbox in one of 3 places: the left-hand side at the top, right-hand side at the leading or on top of the headbox in the.

As soon as opened, get rid of the back glass by raising it up using the lift channel (at the bottom of the glass), and then pull it out from the bottom.

Then, open up the back box lamp panel by lifting the latch located on either the left-hand side or right-hand side. The panel can now swing out to you, and offer you access to the circuit boards, plugs, and the bolts. Some Gottlieb pinballs need you to raise up the light panel in order to swing it open.

Now that you are within, you can get rid of the bolts, and any plugs that have wires going down into the machine. You may wish to label these plugs to put them back in the right spot. You may not have to eliminate the plugs, as the electrical wiring must be long enough to enable the headbox to be folded down.

At this moment, you can secure the light panel and change the back glass.
Modern Strong State Pinballs

For Data East, Sega, and Stern Modern pinballs, there is a turnable lock system situated at the back of the headbox. Utilizing the provided secret, turn the lock 90 ° counter-clockwise.

For Williams, Bally, and Gottlieb, you can quickly unlatch the back box at the back of the maker. This is a basic setup and needs no tools.

You're done if you can now fold down the head box onto the cabinet. Make certain you utilize some foam, heavy cardboard, or blankets to secure the headbox from rubbing on the cabinet. Foam is best, as it will likewise help keep the back glass in place.

You need to get inside if you can not fold the head box down. There is a lock located at the top of the back glass in the center. Use the supplied key to unlock, and remove the back glass by lifting it up from the bottom, then pulling it out from the bottom.

Next, you will need to remove the display panel. (Some newer Williams and Bally pinballs do not have a separate amp panel, it is part of the back glass panel. And later Sega and Stern pinballs use a fluorescent tube for the back glass lighting).

Remove the two bolts, put the back box back together, and fold down the head box onto the cabinet. Make sure you use some foam, heavy cardboard, or blankets to secure the headbox from rubbing on the cabinet. Foam is best, as it will likewise assist keep the back glass in location.
Getting rid of the Legs.

Pinball Device legs are held in place by eight bolts. The modern pinballs have captive nuts or threaded plates inside for the bolts to screw into.

These threaded plates and captive nuts can be harmed, and the usage of extra nuts may have been required. If this is the case, you will need to open the front door of the pinball, slide out the playfield glass, and raise the playfield.

With the front door (coin door) open, move the lock down bar lock across and eliminate the lock down bar. Then slide out the playfield glass, and put in a safe place. Next, raise up the playfield by putting your hand where the ball drains, and lift the playfield up.

You should now have access to any nuts that might have been utilized. As soon as any nuts have actually been eliminated, get more info replace the playfield glass and lock down bar, and lock the front door.

Be sure to mark or keep in mind which legs are for the front and back, as they will be changed in a different way to fit.
Packing the Pinball.

You are now ready to transport your pinball maker. Prior to you pack it, ensure you eliminate the pinballs so they don't bounce around during transportation.

If you are moving the pinball utilizing a van or SUV, it might be simpler to remove the legs just prior to filling the device. Grab a friend to assist and have one of you supporting the pinball, while the other eliminates the front legs.

Make sure you strap the pinball in, as you do not want it moving if you need to stop all of a sudden!

For Electro-Mechanical pinball devices, you need to get rid of the headbox rear gain access to panel to acquire access to the bolts and plugs inside. (Some newer Williams and Bally pinballs do not have a different amp panel, it is part of the back glass panel. And later on Sega and Stern pinballs use a fluorescent tube for the back glass lighting).

If you are moving the pinball using a van or SUV, it might be simpler to remove the legs just prior to filling the device. Grab a friend to have and assist one of you supporting the pinball, while the other removes the front legs.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Tips From the Moving Company Pros: Ways To Move a Pinball Maker”

Leave a Reply

Gravatar